Tektronix MTG100 Manual do Utilizador Página 168
- Página / 250
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Appendix A: Specifications
MTG100 & MTG300 MPEG Generator User Manual
AĆ5
Table AĆ2: Electrical characteristics (Cont.)
Characteristics Description
External reference input
Connector type BNC
Frequency 27 MHz, 1 ppm recommended.
Input level, typical 800 mV ± 200 mV (pĆp)
Input impedance, typical 50 W (at 27 MHz)
ECL control input
Connector type DĆsub, 9 pin
Frequency 62.5 kHz to 10 MHz, select parallel output.
0.5 MHz to 64 MHz, select serial output.
Input level, typical Differential ECL
Termination, typical 110 W, line to line.
Pin assignment 1 DCLK
2GND
3 PSYNC
4 CHCLKEN
5 Shield
6 DCLK
7GND
8 PSYNC
9 CHCLKEN
ECL/TTL/LVDS output (parallel)
Connector type DĆsub, 25 pin (the same connector as Serial output)
Output level (Output on)
(J310101 and above)
Note: Do not connect the Asserted Low pins for singleĆend use.
TTL 0 V to 2.8 V (without termination)
LVDS 0.8 V to 1.60 V (without termination)
ECL*
-1.8 V to -0.9 V (without termination)
Output resistance, typical
(Output off)
350 W at5VtoGNDpin(When the output is off, the power of the buffer amplifier is cut off.)
Data rate 62.5 kBps to 10 MBps
Pin assignment 1 DCLK
2GND
3to10 DATA7toDATA0
11 DVALID
12 PSYNC
13 Shield
14 DCLK
15 GND
16 to 23 DATA 7 to DATA 0
24 DVALID
25 PSYNC
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
- 1
- User Manual 2
- MTG100 & MTG300 2
- MPEG Generator 2
- 071-0615-50 2
- 4
- TableĂofĂContents 6
- Appendices 7
- ListĂofĂFigures 8
- ListĂofĂTables 11
- General Safety Summary 16
- Related Manuals 18
- Contacting Tektronix 19
- Getting Started 20
- Accessories 24
- Initial Product Inspection 25
- Installation 27
- Power Cord Requirements 28
- Applying Power to the 28
- Instrument 28
- Repackaging for Shipment 30
- Functional Check Procedure 31
- Rear Panel Connectors 37
- Display Elements 39
- 12345 67 41
- Using the Menu System 42
- Bezel Menu 44
- Numeric Input 45
- Text Input 46
- PopĆup Message Box 47
- Output Loop Modes 48
- Auto Update Mode 49
- Stress Mode 49
- (MTG300 Only) 49
- Outputting a Transport Stream 51
- 54
- 54
- Figure 2Ć21: INS_SI icon 58
- Reference 60
- PullĆdown Menus 62
- FILE PullĆdown Menu 63
- Select TS File Dialog Box 64
- OUTPUT PullĆdown Menu 65
- Pull-down Menus 66
- Figure 3Ć2: Clock dialog box 66
- CONFIG PullĆdown Menu 68
- PCR Start Value Dialog 70
- Insertion Setup Dialog 71
- Box (MTG300 Only) 71
- TOT Item Dialog Box 73
- STT Item Dialog Box 74
- 0 s to 255 s 75
- Controlling Daylight 76
- Savings Time 76
- UTILITY PullĆdown Menu 78
- Drive Dialog Box 81
- System Dialog Box 82
- Hierarchy Display Icons 85
- Table (TOT) 88
- Program Allocation Table 99
- (PAT) Icon 99
- Hierarchy Display 102
- Transport Stream 103
- Description Table (TSDT) 103
- Network Information Table 104
- (NIT) Icon 104
- Conditional Access Table 105
- (CAT) Icon 105
- Program Map Table (PMT) 107
- Program Clock Reference 108
- (PCR) Icon 108
- Video Elementary Stream 112
- (VIDEO) Icon 112
- Audio Elementary Stream 113
- (AUDIO) Icon 113
- AUDIO_AAC and 115
- AUDIO_AC3 Icons 115
- Data Stream (DATA) Icon 116
- Private Section 117
- (DATA_SECT) Icon 117
- DSM_CC Icon 118
- Entitlement Control 119
- Message (ECM) Icon 119
- Entitlement Management 121
- Message (EMM) Icon 121
- GHOST Icon 122
- Private Information (PRI) 123
- Adaptation Field Error 124
- (ADFERR) Icon 124
- NULL Icon 124
- GARBAGE Icon 125
- SDT, BAT, EIT, RST, ST 125
- DIT, SIT, LIT, ERT, ITT 125
- PCAT, SDTT, DCT, and DLT 125
- TDT and TOT Icon 127
- MGT and PIT Icons 129
- TVCT, CVCT, RRT, EIT 131
- CETT, and EETT Icons 131
- (MTG300 only) (Cont.) 132
- System Time Table (STT) 133
- SĆTMCC and MĆTMCC 134
- Transport Stream (TS) 135
- Non TS Icon 135
- INS_SI Icon 135
- INS_TS Icon 136
- INS_TDT and INS_TOT 137
- INS_STT Icon 138
- Replacing Section Data 140
- Section Modes 142
- Replacement Modes 143
- Inserting Section Data 145
- Adding Jitter 148
- Interval Jitter Function 149
- Value Jitter Function 151
- Preset File 154
- Saving a Preset File 155
- Loading a Preset File 156
- An Example Preset File 157
- File Operations 158
- Copying a file 159
- Deleting a file or folder 161
- Appendix A: Specifications 164
- Appendix B: Using MTG Comm 174
- Installing MTG Comm 175
- Creating a Desktop 176
- Shortcut Icon 176
- Connecting Your PC(s) to 177
- Setting Ethernet Network 177
- Parameters 177
- MTG Comm 180
- Operating Basics 180
- Starting and Exiting MTG Comm 181
- Elements of the MTG Comm 182
- for File Transfers 184
- Using the MTG Comm 185
- View Menu 190
- Remote Menu 191
- Utility Menu 191
- Help Menu 192
- Tutorials 193
- Uploading a File to the PC 195
- Automatic Determination 196
- 200
- Elements of the ReMux Window 201
- Using the ReMux Menus 204
- Edit Menu 205
- ReMux Menu 205
- Window Menu 206
- ReMux Tutorials 207
- 208
- 208
- 208
- " (Execute) 211
- ReMux to MĆTMCC TS 212
- 216
- 216
- 216
- DeMux MĆTMCC TS Mode 219
- Procedures 224
- Internal Clock Frequency 225
- ASI Output 226
- 227
- ! 227
- 227
- ! 227
- SSI Output 228
- 230
- " 230
- Parallel Output 231
- 232
- 232
- 232
- 232
- Serial Output 233
- External Clock Input 235
- External Reference Input 237
- Exterior Inspection 240
- Exterior Cleaning 241
- Glossary 242
- TS (Transport Stream) 245
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.101 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais