search

Tektronix Camcorder 1780-R Manual do Utilizador Página 107

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 188
  • Índice
  • MARCADORES
    • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 106
Operating Instructions
1780R-Series Operator’s Manual
3–55
Left CRT display
Figure 3–26: Configure Menu Screen, page 3
Table 3–8: Configure Menu Selections, page 3
CW SYNC When CW subcarrier is used for vectorscope reference, wfm sync
source can be INT or EXT.
SLOW SWP TRIG Select positive or negative transition of the input signal to trigger slow
sweep.
BAUD RATE Select the baud rate for the serial interface.
VECT READOUT <ON> enables on-screen readouts of data during vectorscope
operation. <OFF> disables the readout. Full-screen menus are not
affected.
WFM READOUT <ON> enables on-screen readouts of data during waveform monitor
operation. <OFF> disables the readout. Full-screen menus are not
affected.
BEEP Beep is either on or off. When on, audio indicates when touch screen
selections have been made.
KNOB ASSIGN
TIMEOUT
When <ON>, with vectorscope CRT selected, will revert to waveform
CRT selection after 30 seconds of no knob activity.
VERSION The version of software currently installed.
Operating Instructions
1780R-Series Operator’s Manual
3–55
Left CRT display
Figure 3–26: Configure Menu Screen, page 3
Table 3–8: Configure Menu Selections, page 3
CW SYNC When CW subcarrier is used for vectorscope reference, wfm sync
source can be INT or EXT.
SLOW SWP TRIG Select positive or negative transition of the input signal to trigger slow
sweep.
BAUD RATE Select the baud rate for the serial interface.
VECT READOUT <ON> enables on-screen readouts of data during vectorscope
operation. <OFF> disables the readout. Full-screen menus are not
affected.
WFM READOUT <ON> enables on-screen readouts of data during waveform monitor
operation. <OFF> disables the readout. Full-screen menus are not
affected.
BEEP Beep is either on or off. When on, audio indicates when touch screen
selections have been made.
KNOB ASSIGN
TIMEOUT
When <ON>, with vectorscope CRT selected, will revert to waveform
CRT selection after 30 seconds of no knob activity.
VERSION The version of software currently installed.
Vista de página 106
1 2 ... 102 103 104 105 106 107 108 109 110 111 112 ... 187 188

Comentários a estes Manuais

Sem comentários
Manuais e produtos relacionados com não Tektronix Camcorder 1780-R
não Tektronix ATM150 Manual do Utilizador   (280 páginas)
não Tektronix TDS 500B Manual do Utilizador   (6 páginas)
não Tektronix TM506 Manual do Utilizador   (12 páginas)
não Tektronix Wireless Office Headset 2711 Manual do Utilizador   (140 páginas)
não Tektronix THS720P Manual do Utilizador   (7 páginas)
não Tektronix 11402A Manual do Utilizador   (71 páginas)
não Tektronix 475A Manual do Utilizador   (80 páginas)
  • A & T International Eddie Bauer Kubota Air Logic Unger
  • ILive Leitores de CD Nikon Flashes para câmaras fotográficas/vídeo Craftsman Carrinhos e suportes multimédia NEC Lâmpadas para projetor Gardena Tesouras
  • Samsung HW-E551 Pulnix TM-7EX Samsung GT-S3802 Noctua NH-C12P SE14 Listen-technologies Satellite Radio
  • Acer Aspire 5570 Manual do Proprietário Frigidaire FFAD3033R1 Ficha de Especificações Acer EB243Y Manual do Utilizador Nokia E51 Manual do Utilizador

    • © 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.081 s |
    Manymanuals.com Manymanuals.de Manymanuals.fr Manymanuals.it
    Manymanuals.pl Manymanuals.cz Manymanuals.es Manymanuals-pt.com